![snap on modis ultra 2 channel labcope snap on modis ultra 2 channel labcope](https://i5.walmartimages.com/asr/471150b9-0a8e-41e3-966b-c03f7633dbff.897733a3e6acc2a2e159663b96d83c92.jpeg)
In addition, with the lead set still hooked up, you have enough cable to put the MODIS right inside the car when you to take it for a test drive. Eliminate the worry of balancing it under the hood of the car or on a fender. Set up a station for the MODIS and keep it there. The ST3 Test Lead Kit for Snap-on MODIS contains 4 test leads that are shielded tip-to-tip and 10-ft long: long enough to reach from the engine compartment and into the back seat if needed.
![snap on modis ultra 2 channel labcope snap on modis ultra 2 channel labcope](https://www.picclickimg.com/d/l400/pict/203651247738_/Snap-On-Modis-Edge-Scanner-2-Channel-Scope-V.jpg)
![snap on modis ultra 2 channel labcope snap on modis ultra 2 channel labcope](https://storage.bhs.cloud.ovh.net/v1/AUTH_e7d15450bedd40b9b599e075527df3cb/minneapolis/_Snapon_Modis_Ultra__3000_Montrose_5aaa43cb74c92.jpg)
Keep your MODIS on the cart Set up a station for the MODIS and keep it there. The ST3 Test Lead Kit for Snap-on MODIS includes a Ground Pigtail to organize multiple grounds from test leads and amp probes, etc. The ST3 Test Lead Kit for Snap-on MODIS contains 4 test leads that are shielded tip-to-tip and 10-ft long: long enough to reach from the engine compartment and into the back seat if needed. Ground stacking becomes an issue when using more than one channel, and a potential danger when all four channels are utilized. The ST3 Test Lead Kit for Snap-on MODIS solves these problems. Plus, when using multiple channels ground stacking becomes a problem. Snap-on Modis EEMS300 4 Channel Lab Scope Module 204HLA-025492.
![snap on modis ultra 2 channel labcope snap on modis ultra 2 channel labcope](https://m.media-amazon.com/images/I/51jYcFPV3wL.jpg)
The MODIS is great tool but it's lab scope test leads are too short for test drives. 17 product ratings - Snap-On Modis Ultra EEMS328 V19.4 Automotive Diagnostic Scan Tool DOM Euro Asian. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. arsenic and chromium from chemically treated lumber.crystalline silica from bricks and cement and other masonry products, and.WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Īdditionally, for certain products sold on AESwave, we also provide the following warnings based upon California law:įor Tools - California requires the following notice: Proposition 65 entitles California consumers to warnings for products that contain chemicals known to California to cause cancer and birth defects or other reproductive harm if those products expose consumers to such chemicals above certain threshold levels.ĪESwave provides the following warning for products linked to this page: Please see the California state government official website for more information: California Proposition 65 Please Log in or Create an account to join the conversation.Proposition 65 requires businesses to notify Californians about significant amounts of chemicals in the products they purchase. I'm sure it's probably a much better tool and newer.Īny inputs will be greatly appreciated.
#Snap on modis ultra 2 channel labcope software#
Below is a link to the scanner im referring to.ī/products/diagnostics/modis-system.aspĪlso she has a snap on solus edge with 15.2 software at a cost of 1700 but not sure if i should go that route as i think to me it's a little expensive being that is not something i will be using all the time. The snap on dealer told me it has 12.2 software so i'm assuming its up to 2012 which would be more than enough for me, also the selling price its 700. I'm a diyer and from time to time i'm in need of a scanner that i can do live data, graphing and any other bidirectional controls not wanting to spend lot of money on it as it's for the weekend jobs. I want to ask your opinion on an older Snap On Modis EEMS300 not sure if anyone has experience on them and just looking for advise on it as to how these performs based on someone else experience.